- Author: Review by ComputeNest Team
- Category: Workspace Setup
- Product Reviewed: Ugreen Nexode 200W Desktop Charger
- Affiliate Link: Buy Ugreen Nexode 200W Desktop Charger on Amazon
Affiliate Disclosure: ComputeNest is reader-supported. Some of the links in this article are affiliate links (marked as “Sponsored”), meaning that if you click through and make a purchase, we may earn a small commission at no additional cost to you. This helps support our independent hardware testing and in-depth reviews. We only recommend products we have personally vetted and tested.
TL;DR: ComputeNest Quick Verdict
| Aspect | Rating / Detail |
|---|---|
| ComputeNest Rating | ⭐⭐⭐•½ (4.5 / 5) |
| Port Layout | 4x USB-C + 2x USB-A (6 ports total) |
| Max Single-Port Output | 100W (USB-C1 and USB-C2) |
| Dual-Port Power | 100W + 100W concurrent output (USB-C1 + USB-C2) |
| Measured Conversion Efficiency | Up to 91.70% (220V 50Hz) / 90.23% (110V 60Hz) |
| 1-Hour Full-Load Thermals | 53.3°C (127.9°F) max temp (under 200W load at 110V 60Hz) |
| MacBook Pro 16″ Charge Time | 2 hours 3 minutes (0 to 100%) |
| Bottom Line | A desktop power station that eliminates workspace cable clutter. With two concurrent 100W outputs and industry-leading thermal control, it is the best premium charger for multi-device setups, despite minor quirks like power redistribution blinks. |
Introduction: The Evolution of Workspace Power
For modern multi-device users, managing power has become a constant logistical challenge. A typical high-performance workspace contains a primary work laptop, a secondary machine or tablet, a smartphone, wireless headphones, and miscellaneous desk accessories like light bars or mechanical keyboards. Relying on individual brick chargers for each device creates a tangled mess of cables under the desk and occupies every available wall outlet.
While wall-plug multi-port chargers have gained popularity, they have a major ergonomic drawback: heavy charging bricks plugged directly into wall outlets tend to wobble, slip out, or block neighboring sockets.
Enter the desktop-oriented power station. By using a dedicated AC extension cord that runs from the wall to a sleek hub sitting flat on your desk, these chargers bring the ports directly to your workspace. The Ugreen Nexode 200W Desktop Charger (Model CD271) is currently one of the most powerful examples of this category. Featuring four USB-C ports and two USB-A ports, it promises to supply a massive 200W of total output.
We put the Nexode 200W through our rigorous in-house lab evaluations, measuring charging speeds, standby draw, conversion efficiency, ripple voltage, and thermal management. Here is our detailed, hands-on verdict.
1. Unboxing, Design, and Build Quality
The Nexode 200W arrives in Ugreen’s signature premium packaging, including:
* The Nexode 200W Charger unit (Model CD271)
* A 6.6-foot (2m) grounded AC power cord with a thick, heavy-duty build
* A 3.3-foot (1m) dual USB-C to USB-C 100W cable with a premium woven design (USB 2.0 data rate)
* Instruction manual and warranty documentation
The charger itself is a solid, square block measuring 101 x 101 x 33 mm (3.96 x 3.96 x 1.28 inches). It weighs in at 515g (1.17 lbs), giving it a reassuringly dense and premium feel. With a total volume of approximately 336 cm³, the charger achieves a power density of 0.59 W/cm³. This is remarkably compact for a 200W power supply, thanks to the integration of GaN (Gallium Nitride) semiconductors.
On the bottom, Ugreen has placed four circular rubber feet that prevent the charger from sliding around when you plug in devices. The body is finished in a clean matte space-gray plastic with black accents, designed to blend in seamlessly with modern desk setups.
Convenient International Travel: The grounded AC cable uses a standard C5 “cloverleaf” connector on the back of the charger. If you travel internationally, you don’t need to bring plug adapters; you can simply purchase a cheap local C5 cable for the country you are visiting and plug it directly into the back of the charger.
2. Port Specifications and Charging Protocols
The front panel layout is clean and clearly labeled:
[ C1: 100W ] [ C2: 100W ] [ C3: 65W ] [ C4: 65W ] [ A1: 22.5W ] [ A2: 22.5W ]
To verify the supported charging protocols, we connected our calibrated ChargerLAB POWER-Z KM002C analyzer to each port.
USB-C1 and USB-C2 Protocols:
- Supported Protocols: Apple 2.4A, Samsung 5V 2A, BC1.2, QC3.0, QC4+, QC5, AFC, FCP, SCP, PD3.0, and PPS.
- Fixed Power Delivery (PDO) Profiles: 5V 3A, 9V 3A, 12V 3A, 15V 3A, and 20V 5A (up to 100W).
- PPS Range: 3.3V to 21V at 3A.
USB-C3 and USB-C4 Protocols:
- Supported Protocols: Identical to C1/C2 with the addition of Huawei FCP.
- Fixed PDO Profiles: 5V 3A, 9V 3A, 12V 3A, 15V 3A, and 20V 3.25A (up to 65W).
USB-A1 and USB-A2 Protocols:
- Supported Protocols: Apple 2.4A, QC3.0, AFC, FCP, and SCP (up to 22.5W).
This protocol selection is outstanding. Whether you are fast-charging an iPhone, a Samsung Galaxy (via PPS), a Huawei flagship (via SCP), or a USB-C laptop, the Nexode 200W has you covered.
3. Real-World Charging Benchmarks
To evaluate the real-world performance, we tested the Ugreen Nexode 200W Desktop Charger against several demanding devices.
MacBook Pro 16-Inch (2021) Charge Test
We connected a depleted 16-inch MacBook Pro 2021 (with M1 Max chip) to USB-C1. The laptop immediately negotiated a 20V profile and pulled a steady 94.2W of power.
We monitored the charge curve from 0% to 100%:
* 30 Minutes: Charged to 44%
* 60 Minutes: Charged to 79%
* Full Charge Time: 2 hours and 3 minutes
The charging speed was identical to Apple’s stock 140W single-port charger when charging over USB-C to USB-C, demonstrating excellent and stable power delivery.
PPS Fast Charging (REDMAGIC 7 Pro)
We tested charging compatibility with a REDMAGIC 7 Pro gaming phone, which relies on Programmable Power Supply (PPS) for its ultra-fast charging. The Nexode 200W successfully triggered the PPS protocol, drawing 54W of power. This is an exceptional result, as many multi-port chargers fail to trigger PPS at high wattages, dropping down to standard 18W PD.
4. Power Distribution Guidelines: How the 200W is Shared
One of the most impressive feats of the Nexode 200W is its ability to output 100W + 100W concurrently from the C1 and C2 ports. This means you can fast-charge two 14-inch MacBook Pros or regular-charge two 16-inch MacBook Pros at full speed simultaneously.
However, as you connect more devices, the internal controller dynamically redistributes the total 200W budget. Here is how the power is divided based on port usage:
Two-Port Configurations:
- C1 + C2: 100W + 100W (Max 200W total output)
- C1 + C3: 100W + 65W (Max 165W total output)
- C3 + C4: 65W + 65W (Max 130W total output)
- C1 + A1: 100W + 22.5W (Max 122.5W total output)
- A1 + A2: 10W + 10W (Max 20W total output)
Three-Port Configurations:
- C1 + C2 + C3: 65W + 65W + 65W (approx. 195W total)
- C1 + C2 + A1: 100W + 65W + 22.5W (approx. 187.5W total)
- C1 + A1 + A2: 100W + 10W + 10W (approx. 120W total)
Four-Port Configurations:
- C1 + C2 + C3 + C4: 65W + 45W + 45W + 45W (official guideline) or 60W + 45W + 46W + 18W (measured in our labs).
Multi-Port Power Drops: In our multi-port testing, we noted a slight discrepancy in four-port mode. When all four USB-C ports were loaded, the USB-C2 port dropped to 45W instead of maintaining the official 65W guideline limit, and the USB-C4 port was restricted to 18W when C3 drew 46W. If you require full 65W output on a secondary laptop, make sure you do not occupy all four USB-C ports simultaneously.
Six-Port Configuration (All Ports Loaded):
- C1 + C2 + C3 + C4 + A1 + A2: 65W + 40W + 31W + 20W + 10W + 7W (200W total).
Power Renegotiation Blinks: Like almost all multi-port GaN chargers, when you plug in or unplug a device, the charger temporarily cuts power to all other ports for 1-2 seconds. This is normal behavior: the internal smart chip is renegotiating the power distribution profiles to ensure that no device is overloaded.
5. Lab Test Results: Efficiency, Ripple, and Thermals
A premium charger must deliver clean, efficient power without generating excessive heat. We subjected the Nexode 200W to our standard lab benchmarks.
Standby Power Consumption
Standby power is the electricity consumed when the charger is plugged into the wall but no devices are connected.
* At 220V 50Hz: 0.228W (translates to ~2.0 kWh per year)
* At 110V 60Hz: 0.044W (translates to ~0.39 kWh per year)
These numbers are outstandingly low, easily passing the strict EU ErP Lot 6 standby power regulations. You do not need to unplug this charger when not in use.
Conversion Efficiency
We measured the ratio of output power to input power across various loads to evaluate efficiency.
| Output Voltage / Current | Efficiency at 110V 60Hz | Efficiency at 220V 50Hz |
|---|---|---|
| 5V 3A (15W) | 79.43% | 78.38% |
| 9V 3A (27W) | 84.12% | 83.90% |
| 15V 3A (45W) | 88.54% | 88.20% |
| 20V 5A (100W) | 90.23% | 91.70% |
Excluding the low-voltage 5V rail (which is naturally less efficient), the average conversion efficiency is near or above 90%. This is an excellent result for multi-port desktop power stations, meaning very little energy is wasted as heat.
Ripple Voltage (Power Cleanliness)
Ripple voltage refers to the residual AC fluctuations in the DC output. Lower ripple indicates higher-quality components and cleaner power, which extends the lifespan of your connected devices.
* No-Load Ripple (5V): Max 32 mVp-p / Min 16 mVp-p
* Full-Load Ripple (20V 5A): 16 mVp-p (at 220V 50Hz) / Max 32 mVp-p
A peak-to-peak ripple of 32 mVp-p is extremely low. It indicates that the internal filter capacitors are performing exceptionally well, keeping your expensive devices safe from electrical noise.
Thermal Performance (1-Hour Stress Test)
We placed the Nexode 200W inside a temperature-controlled chamber at 25°C (77°F) and ran it at the full 200W load for a continuous hour. We then captured surface temperatures using a thermal camera.
- At 220V 50Hz: Front max 50.5°C (122.9°F) | Back max 51.8°C (125.2°F)
- At 110V 60Hz: Front max 51.7°C (125.1°F) | Back max 53.3°C (127.9°F)
To put these numbers into context, many 65W wall-chargers exceed 60°C under load. For a 200W charger to remain below 54°C on all exterior surfaces is a testament to Ugreen’s excellent GaN cooling architecture and thermal distribution. The casing will feel warm to the touch, but never hot enough to cause concern.
6. Ugreen Nexode 200W vs. Anker Prime 240W
To see how the Ugreen Nexode 200W stack up against the competition, we compared it side-by-side with its closest rival: the Anker Prime 240W GaN Charging Station.
| Feature | Ugreen Nexode 200W (CD271) | Anker Prime 240W Charging Station |
|---|---|---|
| Total Power Budget | 200W | 240W |
| Total Ports | 6 (4x USB-C, 2x USB-A) | 4 (3x USB-C, 1x USB-A) |
| Max Single-Port Output | 100W | 140W (USB-C1) |
| Dual 100W Output | Yes (C1 + C2 = 100W + 100W) | No (C1 + C2 = 140W + 100W max) |
| Weight | 515g (1.17 lbs) | 635g (1.4 lbs) |
| Footprint (Volume) | 336 cm³ | 412 cm³ |
| Power Cable Type | Grounded C5 Cloverleaf | Grounded C5 Cloverleaf |
| Price | ~$129.99 | ~$199.99 |
While the Anker Prime offers a higher overall wattage (240W) and a faster single-port speed (140W via PD3.1), the Ugreen Nexode 200W offers two distinct advantages: it has two more ports (6 vs 4) and is significantly more affordable, making it a better pure desk organizer.
7. The Cons: Where the Nexode 200W Falls Short
No hardware is perfect, and we identified a few drawbacks during our long-term usage:
- Momentary Power Drops: As mentioned, plugging in a new device interrupts power to all other devices for 1-2 seconds. If you are transfering data from a USB-C hard drive powered by the charger, the connection will drop.
- USB-C2 Power Drops in Multi-Port Mode: When utilizing 4 or more ports, USB-C2 drops to 40W–45W. If you have two laptops plugged into C1 and C2, adding a phone can suddenly cause the second laptop to stop charging or charge slowly.
- USB-A Limitations: The two USB-A ports share a power line. If you plug devices into both A1 and A2, they drop to 10W each, which is slow for modern accessories.
- Not Travel-Friendly: At 515g, plus the thick 2m AC power cord, the total weight exceeds 800g. This is a charger designed to sit permanently on your desk, not in a backpack.
8. Final Verdict: Who Should Buy It?
The Ugreen Nexode 200W Desktop Charger is a top-tier workspace accessory. Its raw power, dual 100W concurrent charging capability, clean output, and exceptional thermal control justify its premium placement in the market. It successfully replaces a drawer full of individual bricks, turning a messy desktop into a streamlined, high-efficiency workspace.
Buy it if you:
- Have a complex desk setup with multiple USB-C laptops, tablets, and phones.
- Want to fast-charge two laptops simultaneously at 100W each.
- Value low surface temperatures and clean, low-ripple power delivery.
- Want to declutter your desk by running a single AC cord to your workspace.
Skip it if you:
- Need a lightweight, portable charger for travel (look for a folding-prong 65W or 100W wall plug instead).
- Have a high-power laptop that requires 140W PD 3.1 charging (like the 16-inch MacBook Pro at maximum speed).
- Cannot tolerate momentary power drops on other ports when plugging in a new device.
Final Score: 9.0 / 10
Frequently Asked Questions (FAQs)
Does the Ugreen Nexode 200W support PPS fast charging?
Yes. The Ugreen Nexode 200W supports Programmable Power Supply (PPS) on all four of its USB-C ports. In our testing, it successfully triggered high-power PPS charging on compatible devices, outputting up to 54W.
Is the Ugreen Nexode 200W a good travel charger?
No. While it can function as a travel charger because of its 100-240V universal voltage support, it is not ideal. The charging unit weighs 515g, and the heavy 6.6-foot AC power cable adds substantial bulk. For travel, a compact 100W or 65W wall plug is highly recommended.
Why do my devices disconnect for a second when I plug in another device?
This is a standard safety feature called power renegotiation. The internal smart chip must recalculate how to share the 200W power budget among the active ports. To prevent sending too much voltage to a low-power device (like an iPhone), it temporarily drops the connections, applies the new power profiles, and resumes charging.
Does the Ugreen Nexode 200W come with a USB-C cable?
Yes. It includes one premium 3.3-foot (1m) woven USB-C to USB-C cable that supports up to 100W charging. However, you will need to supply your own cables for the remaining five ports.
What is the model number of this charger?
The model number is CD271.
About the Author
The ComputeNest Team is a collective of tech enthusiasts, hardware engineers, and product specialists dedicated to delivering honest, hands-on, and lab-tested reviews. With backgrounds spanning audio engineering, smart home design, mobile ecosystems, and workspace ergonomics, our mission is to cut through marketing hype and help readers make informed buying decisions.